AC, Furnace & Plumbing Services in St. Charles, MO

Responded to no cooling complaint on 17-year-old Lennox system. Upon arrival, found outdoor condenser coil heavily obstructed with dirt, debris, and organic matter, severely restricting airflow through fins. Condenser coil cleaning was required to restore proper system operation and airflow. Unit located at ground level in mulched area with significant leaf litter and environmental contamination contributing to restricted airflow condition.

Responded to emergency water leak in basement caused by disconnected A/C condensate drain hose. Upon arrival, found the drain line had become detached from the floor drain, resulting in active water discharge onto the basement floor with visible pooling and moisture damage to the concrete surface. Reconnected the condensate drain hose to the proper drain outlet and secured the connection to prevent future disconnection. Verified proper drainage flow and confirmed the system was operating correctly with no further leakage.

Replaced evaporator coil in Carrier air handler unit (serial number 2616a84870) located in basement installation. Installed new filter drier as part of the coil replacement procedure. System tested and confirmed operational for cooling mode following completion of warranty repair work.

Responded to no cooling complaint on 3-year-old residential air conditioning system. Upon inspection, diagnosed failed run capacitor with visible degradation and incorrect microfarad reading of 7μF. Replaced defective capacitor with proper OEM specification unit, restored all electrical connections, and verified system operation. Measured supply air temperature at 88.5°F prior to repair; confirmed adequate cooling performance and proper amperage draw after capacitor replacement.

Completed electrical estimate for Generac generator installation. Evaluated existing electrical panel configuration, including main breaker assembly and circuit breaker layout with numbered positions across two columns. Assessed current electrical infrastructure and plumbing manifold system in utility area to determine optimal integration points for generator connection. Documented site conditions and captured detailed photographs of electrical panel and mechanical systems for comprehensive proposal development.

Responded to no cooling complaint on 10+ year old Carrier AC unit located next to garage. Customer reported refrigerant was added one month prior but system still not functioning with indoor evaporator error code displayed. Upon arrival, found unit powered off with fan running. Performed diagnostic evaluation using digital manifold gauge to measure system pressures and temperatures, with readings indicating 58.8°F and 51.8°F temperatures and 29.15" vacuum pressure. Troubleshot evaporator coil operation and refrigerant circuit to identify root cause of cooling failure and error code condition.

Responded to no cooling call on recently installed Lennox system affecting entire home. Upon arrival, performed diagnostic testing using digital multimeter and non-contact voltage tester at equipment junction box and electrical panel. Verified thermostat functionality and temperature settings at wall-mounted control unit reading 72°F. Identified and resolved issue preventing system operation. Unit restored to normal cooling function with proper airflow throughout home. All electrical connections verified secure and system tested through complete cooling cycle to confirm proper operation.

Responded to service call for cooling system not maintaining set temperature on residential unit less than 10 years old located in side yard. Upon arrival, observed outdoor condensing unit with heavy dirt and debris accumulation on exterior panels and surrounding area, indicating extended period without maintenance. Performed diagnostic temperature measurements on unit components using digital thermometer. Found unit operating but compromised by restricted airflow due to excessive dirt buildup on coils and cabinet surfaces. Documented equipment condition with photos showing contaminated exterior surfaces and diagnostic readings. Unit was previously advised to be shut off prior to service visit. Recommended thorough coil cleaning and system evaluation to restore proper cooling capacity and airflow efficiency.

Installed new evaporator coil and thermostatic expansion valve (TXV) on HVAC unit serial number 2208467529. Previous TXV installation from April was incorrect and required replacement. Both components were successfully installed and system restored to proper operation.

Replaced defective flue tee assembly on HVAC system with proper-sized components including 7x4x4 and 7x3 fittings. Removed and disposed of old flue tee hardware, installed new metallic connector junction with secure ductwork connections, and verified proper system operation for both heating and cooling functions.

Responded to report of knocking noise from outdoor AC unit. Upon inspection, found condenser unit operational with accessible exterior-mounted components showing age-related oxidation on refrigerant lines. Identified heavily soiled air filter as contributing factor to system stress. Replaced dirty pleated filter and inspected copper refrigerant piping connections for secure mounting to eliminate potential noise source from loose components or vibration against mounting surface.

Returned to address no cooling condition following previous service visit. Thoroughly cleaned condenser coil to restore proper airflow and heat transfer. Replaced failed capacitor with new unit from van stock and disposed of defective component. Verified system operation using refrigerant manifold gauges, confirming proper pressures, superheat, and subcooling values. Unit restored to normal cooling operation.

Responded to no cooling complaint on residential HVAC system. Performed thorough cleaning of condenser coil to remove accumulated dirt and debris that was restricting airflow and reducing heat transfer efficiency. Replaced failed capacitor with new unit from van stock. System tested after repairs and confirmed proper cooling operation restored. Defective capacitor disposed of per standard procedures.

Addressed water heater flue installation and provided technical consultation regarding flue liner requirements. After thorough inspection and assessment of the existing HVAC system and water heater configuration, determined that flue liner installation was not necessary for this application. Responded to customer inquiries and concerns about proper venting requirements, explaining code compliance and safety considerations. Documented equipment condition and current installation with photographs showing air handler unit, condensing unit with refrigerant lines, PVC condensate drainage, and furnace with existing vent piping configuration in mechanical space.

Responded to service call for non-functional ceiling fan and light fixture in residential kitchen area. Upon inspection, diagnosed electrical issue affecting the ceiling fan unit with wooden blades and integrated lighting. Performed necessary troubleshooting and repairs to restore power and functionality to both the fan motor and light components. Verified proper operation of pull chain controls and confirmed unit was operating safely before completing service.

Performed diagnostic service on 1-year-old residential air conditioning system experiencing excessive condensation issues and resulting air filter clogging. Upon inspection, discovered significant moisture accumulation on indoor HVAC ductwork and equipment surfaces, with visible water droplet formation indicating improper temperature differential or airflow concerns. Evaluated refrigerant charge levels, inspected condensate drainage system, and assessed indoor air handler and outdoor ground-level condenser unit operation. Documented conditions with photographic evidence showing condensation on metal ductwork panels and exterior unit installation. Contacted customer to review diagnostic findings and discuss recommended repairs to resolve moisture-related performance issues affecting system efficiency and indoor air quality.

Installed a 40-gallon State ProLine commercial-grade gas water heater in basement utility area with complete copper piping connections, brass shut-off valves, and proper venting through metallic duct system. Connected unit to existing pressure tank system with appropriate compression fittings and integrated galvanized supply lines with copper distribution piping using brass transition fittings and ball valves for system isolation.

Responded to service call for standby generator that was running test cycles but not producing power output. Upon arrival, inspected the backyard-mounted generator system and associated transfer switch panel. Performed diagnostic testing using clamp meter to verify absence of power generation during simulated test cycle. Identified issue with generator control panel and transfer switch operation preventing power transfer to the electrical distribution system despite engine operation. Inspected circuit breakers, bus bar connections, and generator disconnect switch for proper operation and secure connections. Documented existing conditions of electrical panel components including 50-amp and 60-amp breakers, control wiring, and safety disconnect mechanisms. Reviewed warning labels and confirmed proper safety protocols. Provided assessment of necessary repairs to restore full generator functionality and power transfer capability.

Responded to no-cool call on ground-level unit U10 where water was pooling in basement around furnace. Upon inspection, discovered significant corrosion and rust on condensate drain pan and surrounding metal panels, indicating long-term moisture exposure. Advised customer to turn off A/C system and run fan only to prevent further water accumulation until drain line issue could be properly addressed. Documented extensive rust damage on equipment panels and deteriorated condensate management components with photos for service records.

Responded to customer complaint of AC unit making repeated "revving up" noises in a cycling pattern while still maintaining cooling capacity. Upon inspection of 2-year-old Lennox system, found outdoor condenser unit's intake grille and filter heavily restricted with dust, dirt, and debris accumulation. Restricted airflow was causing compressor to cycle on high-pressure cutout as unit struggled to maintain adequate heat exchange. Removed and cleaned condenser filter, cleared debris from intake grille mesh screening. Verified proper airflow restoration through condenser coil. Cycled unit through multiple cooling cycles to confirm elimination of abnormal sound patterns and return to normal operating parameters.