AC, Furnace & Plumbing Services in St. Charles, MO

Responded to no cooling complaint on residential air conditioning system. Upon arrival, unit was found in off position. Performed thorough inspection revealing outdoor condenser coil heavily contaminated with dirt, dust, and debris buildup, significantly restricting airflow and reducing heat transfer efficiency. Indoor air filter showed moderate dirt accumulation. Cleaned outdoor coil to restore proper airflow and system performance. Verified system operation and cooling capacity restored to normal parameters.

Arrived on-site following previous day's diagnostic where system was found frozen. Performed system evaluation under extreme heat conditions with ambient temperatures reaching 99°F. Utilized Fieldpiece SMAN manifold gauge to assess refrigerant pressures and temperatures on R-410A system, recording high-side pressure at 336.1 PSIG with superheat at 161°F and subcooling readings. Documented system operating parameters and current conditions for repair recommendations, which will require additional authorization to proceed.

Responded to emergency no-cool call for 2019 Trane system unable to maintain temperature below 77°F. Upon inspection, found condenser coil heavily obstructed with dirt, debris, and organic material buildup significantly restricting airflow through fins. Removed side panel and documented severe contamination on condenser coil assembly. Performed thorough coil cleaning to remove accumulated debris and restore proper airflow. Inspected copper refrigerant lines showing age-related oxidation but no leaks detected. System restored to normal cooling operation following coil cleaning service.

Responded to no cooling complaint on ground-level unit U10. Upon inspection, advised customer to shut off air conditioning system immediately and operate only the fan mode to prevent potential compressor damage. Documented equipment condition with photos showing air handler assembly, evaporator coil with visible dust accumulation, and associated ductwork in utility space.

Responded to no cooling complaint on 16-year-old residential air conditioning system. Upon arrival, performed comprehensive diagnostic evaluation of both indoor Lennox furnace/air handler unit and outdoor condensing unit. System had received maintenance service in April but was failing to maintain desired indoor temperatures. Conducted visual inspection of equipment, checked refrigerant pressures, tested electrical components, and verified proper airflow through the system. Evaluated condenser operation, blower motor function, and thermostat communication. Documented equipment condition with photos of basement air handler installation and exterior condensing unit. Identified root cause of cooling deficiency and completed necessary repairs to restore system to proper operating condition. Tested system operation post-repair to confirm adequate cooling capacity and temperature differential across evaporator coil. Unit cycling properly and maintaining setpoint upon departure.

Responded to service call for corroded Honeywell thermostat requiring replacement. Upon inspection, confirmed severe corrosion on thermostat housing and internal components, rendering unit inoperable and unsafe for continued use. Removed defective thermostat from wall mount, disconnected wiring, and documented existing conditions with photographs for customer records.

Responded to service call for furnace with air filter access issue stemming from improper 2018 installation. Upon inspection, identified and removed obstructing screw from air handler cabinet that was preventing filter door from opening correctly. Corrected cabinet panel alignment and verified proper clearance for filter removal and replacement. Inspected internal components including blower motors, control board, and wiring harness—all found in satisfactory operating condition with no signs of damage or excessive wear. Noted significant dust accumulation on existing filter, which was addressed. Tested filter door operation multiple times to ensure smooth access for future maintenance. System operational and filter access fully restored.

Installed REME HALO air purification system on heating and cooling unit less than one year old. Verified electrical connections and proper operation with multimeter testing, confirming system functionality upon completion.

Performed comprehensive cooling system maintenance and tune-up on HVAC unit with system operating properly upon arrival. Conducted thorough inspection of air handler components including blower motor assembly, electrical connections, and air filtration system. Verified proper motor operation, checked wire connections and grounding, inspected blower wheel for debris accumulation, and confirmed air filter condition and proper installation within housing.

Responded to no cooling complaint on 7-year-old outdoor unit. Upon inspection, found failed dual run capacitor with visible signs of deterioration. Replaced defective capacitor with manufacturer-approved replacement, restored power, and verified proper system operation with all electrical connections secure. Unit cooling normally at time of departure.

Responded to service call for non-functioning outlets in two bathrooms and exterior locations. Upon arrival, verified that no circuit breakers were tripped in the main electrical panel. Conducted comprehensive inspection of the electrical distribution system, including examination of the main breaker panel and exterior meter assembly. Inspected all circuit breakers for proper operation and verified panel integrity. Documented existing electrical infrastructure conditions, including the main service panel mounted in utility area and exterior meter installation showing signs of weathering and corrosion on enclosure. Identified potential issues requiring further investigation to isolate the cause of outlet failures in affected areas.

Responded to no cooling complaint on 16-year-old basement unit. Upon inspection, discovered severe corrosion and rust throughout the evaporator coil assembly, with heavy deterioration on copper U-bends and heat exchanger tubes. The extensive corrosion has compromised the coil integrity, resulting in loss of cooling capacity. Recommended complete evaporator coil replacement due to the advanced state of deterioration and provided repair options to restore system functionality.

Replaced failed evaporator coil in air handler unit and installed two 3-inch flex couplings to complete the repair. Removed and disposed of old coil assembly, pressure tested system, and verified proper operation of heating and cooling functions upon completion.

Responded to no-cool complaint with evaporator coil freeze-up on two-year-old residential air conditioning system affecting entire home. Upon inspection, found outdoor condenser coil heavily contaminated with dirt and debris accumulation restricting airflow, contributing to improper system operation and refrigerant pressure imbalance. Performed visual inspection of control board and low-voltage wiring connections, verified all terminations secure at terminal block. Documented condenser coil condition and control board configuration with photos for warranty consideration given unit age. Advised customer of findings and recommended thorough coil cleaning, refrigerant charge verification, and airflow diagnostics to resolve freezing condition and restore proper cooling operation.

Responded to service call for error code displaying on Trane thermostat at front entrance foyer unit. Upon arrival, connected refrigerant manifold and micron gauge to assess system pressures and temperatures, which revealed abnormal readings indicating potential refrigerant or airflow issues. Inspection of outdoor unit discovered significant rust and corrosion on rigid ductwork connections, compromised condensate drainage system with standing water and debris accumulation in drip pan, and deteriorated flexible duct insulation with visible environmental contamination. Documented equipment condition with diagnostic measurements and photographic evidence for repair recommendations.

Responded to service call for AC leak requiring location identification. Upon arrival, performed thorough inspection of HVAC system and surrounding areas. Located source of water leak at air handler unit in mechanical space. Found significant water accumulation on floor surfaces and extensive moisture damage to surrounding flooring, walls, and subflooring materials. Confirmed drain line was not source of issue as previously verified by municipal sewer inspection. Inspected humidifier operation and determined it was not contributing factor to ongoing leak. Traced leak to condensate issue at air handler unit. Documented extensive water damage including deteriorated flooring tiles, wall discoloration, and moisture infiltration in crawlspace area beneath unit. Photographed conditions showing standing water, damaged subflooring, compromised wall surfaces, and affected ductwork area. Identified primary leak source and provided recommendations for necessary repairs to resolve water intrusion

Responded to callback on new installation regarding intermittent loud compressor startup. Performed electrical diagnostics and amperage measurements at the indoor air handler unit to verify proper system operation and determine if hard start kit installation would resolve the issue. Evaluated compressor performance and electrical characteristics to assess whether component addition or unit replacement would be necessary.

Responded to no-cool complaint on Lennox EL18XPV-024-230A01 unit with HFC-410A refrigerant. Upon arrival, found system running but unable to maintain setpoint temperature. Performed electrical diagnostics using clamp meter, recording amperage draw of 333.1 amps, which significantly exceeds normal operating parameters for this 2-ton unit. Advised customer to turn system off immediately to prevent compressor damage. Unit requires further diagnosis to determine cause of excessive amperage draw, likely indicating compressor failure or electrical fault.

Completed electrical fixture installation in basement area per approved estimate. Installed new electrical wiring through floor joists using appropriate cable routing methods with securing clips and junction boxes. Mounted electrical switch assembly with indicator lights in metallic junction box on foundation wall, utilizing flexible conduit for proper wire protection. All work performed to code specifications with proper grounding and secure mounting hardware.

Responded to report of kitchen lights flickering when air conditioning unit activates. Inspected main electrical panel and identified loose neutral connections causing voltage fluctuations during high-load startup conditions. Tightened all neutral bus bar connections, verified proper torque specifications on main breaker terminals, and confirmed all branch circuit connections were secure. Tested system operation through multiple A/C cycling events to verify flickering issue was resolved and electrical system remained stable under load.