AC, Furnace & Plumbing Services in St. Charles, MO

Performed secondary assessment of HVAC system and water heater installation as requested. Documented extensive corrosion on copper water supply lines entering water heater unit, showing significant oxidation with blue-green patina and rust discoloration. Inspected refrigerant line connections at air handler cabinet, noting degraded foam insulation on suction line and service valve accessibility. Photographed corroded plumbing connections and HVAC component conditions for reference and further evaluation recommendations.

# HVAC Cooling System Tune-Up Completed Performed comprehensive annual maintenance on a 6-year-old ground-level air conditioning unit located in the backyard. Accessed property using provided entry instructions and conducted full system inspection and tune-up procedures. ## Work Performed Inspected outdoor condenser unit and found heavy accumulation of dust, dirt, and debris on condenser coils and finned surfaces. Removed back panel to access coil assembly for thorough cleaning. Cleaned condenser coils to restore proper heat transfer efficiency and airflow. Inspected refrigerant lines, copper tubing connections, and insulation for integrity and proper condition. Proceeded to indoor air handler for filter service. Replaced existing air filter with new Purolator filter featuring pleated media and cardboard frame construction to ensure optimal airflow and filtration. Completed standard tune-up checklist including: - Visual inspection of all accessible components - Verification of ref

Completed preventative maintenance tune-up on a 4-year-old air conditioning system located in basement mechanical room. Performed comprehensive system inspection including electrical control board examination, verified all wire connections and relay operations, and documented control panel condition. Inspected and documented heavily soiled air filter showing significant dust and debris accumulation on pleated media, indicating proper filtration but requiring replacement for optimal airflow and system efficiency.

Conducted electrical system assessment and fixture estimate verification. Inspected main electrical distribution panel, documenting circuit breaker configuration and wire routing for existing installation. Performed outlet testing using calibrated electrical tester to verify proper grounding, polarity, and voltage levels, confirming 120VAC reading and correct wiring configuration. Reviewed previous estimate documentation to determine applicability for current scope of work and identify any necessary updates to fixture specifications or installation requirements.

Responded to service callback regarding basement flooding that occurred during previous AC maintenance visit. Upon arrival, documented extensive water damage throughout basement area with visible pooling, moisture staining, and mineral deposits on concrete floor. Customer belongings showed water damage. Investigated source of flooding and inspected water supply connection at HVAC unit, locating blue flexible water line with shutoff valve in attic/crawl space above affected area. Photographed damage extent and plumbing connections for incident documentation. Verified current system operation and confirmed no active leaks present at time of callback inspection.

Responded to callback for air conditioning unit not activating. Upon arrival, inspected 9-year-old system previously serviced with capacitor replacement. Performed diagnostic testing on unit located in interior mechanical closet, checking electrical connections, control board functionality, and verifying capacitor operation. Documented equipment condition and installation configuration for service records.

Replaced maintenance kit on humidifier unit including new filter pad and associated hardware. Unit tested and confirmed operational with proper water flow and electrical connections verified. System returned to normal heating and cooling operation.

# Compressor Replacement Under Warranty Replaced failed compressor on residential air conditioning system under manufacturer warranty. Unit serial number 2204480526 was serviced with new compressor delivered from supplier. System was evacuated, new compressor installed, and refrigerant charge verified using digital manifold gauges. Post-installation diagnostics confirmed proper superheat readings and system operation. Failed compressor retained per warranty requirements for manufacturer return.

Completed comprehensive Elite electrical inspection of residential property. Thoroughly examined main electrical panel, documenting breaker configuration, circuit labeling system, and overall panel condition. Inspected digital utility meter installation, verified proper mounting and seal integrity, and confirmed meter functionality and communication indicators are operational. All electrical components photographed for documentation purposes, with no immediate safety concerns identified during the audit.

Completed preventative maintenance tune-up on 16-year-old Goodman furnace in preparation for heating season. Performed comprehensive system inspection including visual examination of heat exchanger using borescope camera to check for cracks or deterioration, verified proper operation of all safety controls and limit switches, tested ignition system and burner assembly function, checked and adjusted gas pressure, inspected flue venting for proper draft and clearances, cleaned flame sensor, evaluated blower motor operation and amperage draw, replaced air filter, and confirmed adequate airflow throughout system. All components operating within manufacturer specifications with no immediate safety concerns identified. System ready for winter operation.

Completed comprehensive Supertune maintenance service on Trane air handler unit located in basement mechanical room. Performed full system inspection, replaced heavily soiled 16x25x1 air filter that showed significant dust and debris accumulation, checked all electrical connections and components, verified proper airflow and operation, and ensured system is running at optimal efficiency for the cooling season.

Responded to commercial kitchen electrical service call regarding outlet shorting out circuit breaker. Upon inspection, identified faulty outlet circuit causing breaker trips. Verified panel integrity and determined existing panel did not require replacement. Isolated problematic kitchen outlet circuit, tested all connections, and resolved the electrical short condition to restore safe operation.

Completed preventive maintenance tune-up on residential air conditioning system under 10 years old per Home Depot service agreement. Performed comprehensive inspection of indoor air handler unit, verifying proper operation of blower motor assembly, control board functionality, and electrical connections at terminal block. Exterior condenser unit showed moderate dirt and debris accumulation on louvers and coil fins, which was cleaned to restore optimal airflow and heat transfer efficiency.

Responded to no cooling complaint for single HVAC unit located in basement. Upon inspection, performed diagnostic testing using digital multimeter on air handler components, obtaining voltage readings of 416V and 179V on system electrical components. Advised customer to shut off AC unit and leave fan running due to suspected refrigerant leak affecting whole-home cooling performance. Documented equipment condition with photos of testing procedures and air handler coil assembly for further evaluation and repair recommendations.

Replaced failed compressor unit on Trane American Standard system. Removed defective compressor and installed new COM12406 replacement unit, securing it to existing mounting base. Documented old and new compressor installations with photographs per requirements, and retained failed component for warranty processing.

Responded to no cooling complaint on 3-year-old Lennox system. Upon arrival, found outdoor condenser unit with heavily soiled coil fins and significant debris accumulation restricting airflow. Condenser coil cleaning was performed to remove dust, dirt, and debris buildup that was preventing proper heat exchange and causing reduced cooling capacity. Cleared vegetation growth from around unit base. System tested after cleaning and verified proper operation with adequate cooling to thermostat set point.

Completed comprehensive cooling maintenance tune-up on a 9-year-old residential air conditioning system. Performed full system inspection including condenser unit evaluation, filter replacement, and operational testing of all components. Unit was found to be functioning properly with condenser coils showing normal weathering for age; confirmed adequate airflow through finned coil assembly and verified system performance meets manufacturer specifications.

Performed routine preventive maintenance on commercial standby generator equipped with Sync 3.0 control system. Upon arrival, verified generator status displayed "READY TO RUN" with battery inspection advisory on LCD interface. Conducted comprehensive inspection of control panel functions, testing AUTO, MANUAL, and OFF mode selections to ensure proper operational capability. Examined all safety interlocks and warning systems, confirming bypass protection features were functioning correctly. Inspected battery connections and charging system, noting maintenance alert on display panel. Checked all electrical connections, control wiring, and associated mechanical components including pump assembly and corrugated conduit routing. Verified proper operation of ON/OFF switch and navigation controls. Cleaned control panel face and surrounding equipment housing. Reviewed all warning labels and safety placards for visibility and compliance. Discussed available preventive maintenance packages with

Responded to callback for 17-year-old AC system where indoor air handler was running but outdoor unit remained inoperative following previous repair attempt. Inspected thermostat wiring, control board connections, and contactor operation to diagnose communication failure between indoor and outdoor units. Corrected reversed wiring configuration at air handler that was preventing proper signal to outdoor condensing unit, restored proper system operation, and verified both indoor blower and outdoor compressor cycling correctly on cooling demand.

Performed deep cleaning of wall-mounted mini-split air conditioning unit using jet pack cleaning system. Accessed unit via ladder, applied specialized cleaning solution through the system to remove accumulated debris and buildup from internal components and coils, restoring proper airflow and operational efficiency.